Replacing Jayco Pop-Up Camper Remote Control Batteries

If you're looking to replace the batteries in your Jayco pop-up camper remote control, you may be out of luck. While there are plenty of resources for replacing the batteries in a Jayco camper, I could find no information on replacing the batteries in a remote control for a Jayco pop-up camper.

Ensure the battery is connected to the red and white wires on the trailer hitch

To ensure the battery is connected to the red and white wires on the trailer hitch, you must first locate the wires. These wires are typically found in the trailer hitch plug or the trailer hitch connection. Once you have located the red and white wires, you can proceed with the following steps:

Step 1: Check the battery's energy density and ensure it meets the requirements of your Jayco pop-up camper. The energy density will determine the bulkiness of the battery and the amount of stored energy.

Step 2: Identify the positive and negative terminals on the battery. The positive terminal is typically indicated by a red colour, while the negative terminal may be white or black.

Step 3: Connect the battery terminals correctly. Join the positive terminal of the battery to the negative terminal of the camper's wiring harness or the trailer hitch plug. Ensure that the connection is secure and soldered properly.

Step 4: Check for any signs of corrosion on the battery wires. If there is corrosion, clean the wires and apply grease or petroleum jelly under the clamps to prevent further corrosion.

Step 5: Refer to the user manual for your Jayco pop-up camper. The manual should provide specific instructions for connecting the battery to the red and white wires on the trailer hitch.

Step 6: Ensure that the battery is securely mounted in an upright position to prevent electrolyte solution leakage and mitigate the impact of vibrations.

Step 7: Test the battery connection by plugging in the trailer hitch and checking if the battery powers the camper's electrical systems, such as the lights or any other 12-volt devices.

Step 8: If you are unsure or uncomfortable with any of the steps, it is recommended to seek professional help. Improper battery installation can lead to electrical issues or safety hazards.

Check for corrosion on the battery wires

Corrosion on the battery wires can cause electrical problems and reduce the battery life of your Jayco pop-up camper. Therefore, it is important to check for corrosion and clean it if necessary. Corrosion is a common occurrence, often caused by typical wear and tear, and can be identified by a white, blue, or greenish powder surrounding one of the battery terminals, posts, or cables. It will have a granular, powdery texture.

Before you begin, make sure you are wearing heavy-duty gloves and eye protection. Corrosion can damage your skin and eyes, so always wash away any corrosive material that gets on your skin or clothing.

To clean the corrosion, start by disconnecting the battery. Carefully release the cable from the negative terminal first, then the positive terminal. Next, inspect the battery cables for any fraying or corrosion. If the insulation is dry or cracking, the cables will need to be replaced.

You can clean the corrosion while the battery is still in the vehicle, but it is safer to remove it and place it in a shallow bucket or pan to collect the corrosive material. Use a wire brush or scraper to remove any solid, powdery corrosion from around the terminals and dirt from the top of the battery casing. Brush away the corrosion and let it fall into the pan or bucket.

To neutralize the corrosion, you can use a commercial battery terminal cleaner or a baking soda and warm water solution. Dip a rag in the solution and wipe away the corrosion, or use a commercial battery terminal cleaner. Be sure not to dump the solution over the battery to prevent it from leaking into the battery cells and neutralizing the sulfuric acid inside.

Finally, dry and polish the battery using a microfiber cloth. Remove any debris or coating from the terminals with a terminal cleaning brush. Once the battery is completely dry, you can return it to its tray and reconnect the terminals, starting with the positive terminal.

Take your old battery to the shop to avoid confusion

When replacing the batteries in your Jayco pop-up camper remote control, it's important to take your old battery to the shop to ensure you get the correct replacement. This is especially important if you're unsure about the battery model or its specifications. Taking the old battery with you will help you communicate your needs to the salesperson and avoid confusion.

Before you go to the shop, make sure you have a plan for safely disposing of your old battery. Check your local regulations and contact your local sanitation department to understand the proper disposal methods. In most places, single-use batteries can be disposed of in the regular trash, but this varies by location. For example, in California, it is illegal to throw away any kind of battery.

If you're unable to dispose of your old battery in the trash, you can recycle it. Many retailers that sell batteries also offer recycling services or collection bins in partnership with battery recycling programs. These include home improvement stores, office supply stores, and watch repair shops. Some battery manufacturers and recycling facilities also offer mail-in recycling programs.

When taking your old battery to the shop, ensure that you store and transport it properly. Keep batteries in a cool, dry place, at room temperature, and avoid exposing them to extreme temperatures or direct sunlight. Do not store them in plastic bags or mix them with other metal objects, as this can cause a short circuit.

By taking your old battery to the shop, you can ensure that you get the correct replacement and properly dispose of or recycle your old battery. This will help you keep your Jayco pop-up camper remote control functioning properly and avoid any confusion during the replacement process.

Install the new battery in the tray and fasten it with a clamping device

To install the new battery in the tray, carefully connect the terminals. The positive terminal should be connected to the negative terminal of the other battery. Then, place the battery in the tray and fasten it with a clamping device. This is important as vibration is one of the leading causes of an auto battery dying early.

Before installing the new battery, make sure to clean the battery wires if they are dirty and apply grease or petroleum jelly under the clamps to prevent corrosion. Also, ensure that your new battery is fully charged before installing it. Otherwise, you could overburden and destroy the charging mechanism.

Connect the terminals correctly: positive to negative

When installing a battery in your Jayco RV, it is important to connect the terminals correctly. The positive terminal of one battery should be connected to the negative terminal of the other battery. This is known as series wiring and is the correct way to wire batteries in an RV.

Connecting the terminals in this way ensures that the voltage of the battery system is added together, providing the correct voltage for your RV appliances. If the batteries were connected positive to positive or negative to negative, this would be known as parallel wiring and would result in the batteries providing double the current but at the same voltage. This wiring setup is not suitable for RVs as it would not provide the correct voltage to power your appliances.

It is important to take care when connecting the battery terminals to avoid short circuits. Make sure that the terminals are clean and free of corrosion before connecting them. You should also ensure that the batteries are securely mounted and that the connections are protected from vibration and movement, as this can cause damage to the terminals and connections.

If you are unsure about how to connect the batteries correctly, it is recommended that you seek professional help. Incorrectly connected batteries can be dangerous and can cause damage to your RV's electrical system.

Frequently asked questions