Removing Jeep Doors: Quick And Easy?

how long does it take to remove jeep doors

Removing the doors from a Jeep Wrangler is a relatively quick and easy process, even for beginners. It is a common practice, as it allows for a more immersive driving experience and can increase fuel efficiency. The process is basically the same for the front and rear doors: roll down the windows, remove the door check arm, unplug the wiring, drop the two hinge bolts, pull off the limit strap, and lift the door away. The whole process can take as little as 5-10 minutes per door, or up to 30 minutes in total if it's your first time.

Characteristics Values
Time taken to remove Jeep doors 5-30 minutes
Tools required 13mm socket and wrench, flathead screwdriver, ratchet and T50 Torx-drive bit, T40 driver bit
Additional items Wooden blocks, moving blankets, wall-mounted door holder, door cart

shunauto

Fold the side mirrors in

Folding the side mirrors in is an important step when removing the doors of a Jeep, as it prevents the mirrors from being damaged while the doors are being stored. The process of folding the side mirrors in is relatively straightforward and can be done manually by pushing or twisting the mirrors towards the door until they are flat against it. This can be done with one hand, but using two hands may be better as it reduces the chance of applying unnecessary force that could potentially damage the mirrors over time.

For Jeep Wranglers, the process of folding in the side mirrors is the same for both the driver's side and passenger's side. However, for the Jeep Wagoneer, the process may differ depending on whether the vehicle is equipped with power-folding mirrors. In this case, the mirrors can be folded in by rotating the knob towards the rear lift gate.

It is worth noting that in some places, it is illegal to drive without side mirrors, so it is important to either keep the doors on or purchase and attach mirrors to the sides of the windshield to comply with local laws.

Gladiator Door Removal Guide

You may want to see also

shunauto

Roll down the window

Rolling down the windows of your Jeep is crucial when removing the doors. Here's a step-by-step guide on how to do it:

Locate the Window Controls: The window controls are typically found on the driver's side door panel or the center console. Look for the buttons or switches corresponding to each window.

Press the Window Button: Once you've located the controls, press the button or switch for the window you want to roll down. Ensure you press the correct one to avoid rolling down the wrong window.

Safety Tips: Before rolling down the windows, secure any loose items inside your Jeep, such as mobile phones, water bottles, or sunglasses, to prevent them from becoming projectiles. Also, check the weather conditions and avoid rolling down the windows if heavy rain or strong winds are expected.

Benefits of Rolling Down Windows: Rolling down the windows can provide a refreshing breeze and enhance your driving experience. It allows you to feel the fresh air, enjoy scenic views, and create a spacious environment inside the Jeep.

Now that the windows are rolled down, you can proceed with the next steps of removing the Jeep doors, which include unhooking the safety straps, unplugging wiring harnesses (if applicable), and finally, lifting the doors off the vehicle. Remember to store the doors safely to avoid damage.

Jeep JL: Removable Hardtop?

You may want to see also

shunauto

Remove the black safety strap

To remove the black safety strap on the door of your Jeep, follow these steps:

First, locate the black safety strap. There should be one connected to each door. These straps are designed to prevent the door from opening too far.

Once you've found the strap, simply unhook it from the body of the Jeep. Be careful not to break or damage anything in the process. The other end of the strap will stay connected to the door itself.

If you're having trouble removing the strap, make sure to do this step while the door is mostly closed. That way, there's enough slack to get the loop free from the hook.

Now that the black safety strap is unhooked, you can continue with the process of removing the door. Remember to be gentle and careful throughout the process to avoid damaging your Jeep.

  • Roll down the window to make it easier to reach through and lift the door.
  • Fold in the side mirrors to prevent them from being damaged during storage.
  • Unplug the wiring pigtail if your Jeep has power windows and door locks.
  • Locate and remove the two bolts holding the door in place.
  • Be careful with the paint on the door hardware to avoid scratches and chipping.
  • Lift the door straight up to disconnect it from the vehicle.
  • Store the doors in a safe place, such as on a blanket or a wall hinge.
Jeep Doors: Removable or Not?

You may want to see also

shunauto

Unplug the wiring pigtail

Unplugging the wiring pigtail is a crucial step in removing the doors from your Jeep. This step is only necessary if your Jeep has power windows and door locks.

To unplug the wiring pigtail, locate the group of wires bunched together in black cloth that runs from the Jeep's doors to beneath the dashboard. You will then need to press the release on the plastic wire pigtail and disconnect the wiring by pulling the wire backward.

Be careful not to break the plastic clip that holds the wiring pigtail in place.

If you have a high-trim Jeep, it likely has door locks and power windows. These are powered by a bunch of cables that need to be unplugged. You will see a thin black cloth running from the doors to the dashboard. The wire pigtail will have a release that you need to press and gently pull to free the wires.

Once you have unplugged the wiring pigtail, you can move on to the next steps of removing the Jeep's doors.

Uninstalling a Jeep Lift Kit

You may want to see also

shunauto

Remove the nuts and bolts

To remove the nuts and bolts of your Jeep's doors, you will need to use a 13-millimetre socket and wrench. A six-point socket is recommended to minimise the movement of the nut inside the socket and reduce the chances of damaging the paint on the nuts.

Turn the nuts counter-clockwise to loosen them. Be careful not to go crazy with the wrench, as it is easy to damage the paint during this process. Once the nuts are removed, you can move on to lifting the door straight up and off the Jeep.

If you are removing the doors of a Jeep Wrangler JK or JL, you will need a T50 Torx-head drive bit to remove the T50 Torx-head cap nuts at the underside of each hinge. For the JL model, you will also need a T40 Torx driver bit to remove the door catches in the door jambs.

Undoing a Jeep Body Lift: How Hard?

You may want to see also

Frequently asked questions

Removing Jeep doors is a quick and easy process that can be done in 30 minutes or less, even for beginners.

You will need a 13mm socket and wrench, a flathead screwdriver, and a T50 Torx-drive bit or ratchet.

Yes, Jeep doors are designed for quick and easy removal. The process is simple and can be done by one person.

It is recommended to fold in the side mirrors to prevent damage during storage. Most Wrangler and Gladiator models have foldable mirrors.

Store the doors in a cool, dry place. Consider using a door removal tool or wall mount door holder kit to safely store the doors and prevent damage.

Written by
Reviewed by
Share this post
Print
Did this article help you?

Leave a comment