
There are many ways to make camper awning lights. You can use zip ties, command hooks, clips, clothespins, rubber slot fixtures, or strip lights. The method you choose will depend on the type of lights you have and the look you are going for. If you want to use zip ties, you will need to find the perfect spot for your lights, measure the length of the string of rope lights, cut the zip ties to size, string the lights through the holes in the zip ties, and attach the zip ties to the RV awning. If you want to use command hooks, you will need to choose a location for the LED lights, attach the command hooks to the awning, and hang the LED lights from the command hooks. If you want to use clips, you will need lights, a ladder, and awning clips. You may also need additional tools depending on the type of camper awning you have. Once you have everything you need, you can reach up and clip the lights onto the awning.
What You'll Learn
Using zip ties
Step 1: Choose the Perfect Spot for Your Lights
Decide on a location that is both aesthetically pleasing and functional. Consider which area of your camper you will be using the most and the type of atmosphere you want to create. For example, if you want a cosy and inviting ambiance, opt for warm white lights.
Step 2: Measure the Length of the Rope Lights
This step is crucial to ensure you have enough zip ties to secure your lights. Measure the length of your rope lights and cut the zip ties accordingly, leaving about an inch of tail on each one.
Step 3: String the Lights Through the Zip Ties
Start at one end of the rope lights and thread the string through the holes in the zip ties. Repeat this process until all the lights are attached securely.
Step 4: Attach the Zip Ties to the Camper Awning
Wrap the zip ties around the awning until they are tight and secure. Ensure that the lights are evenly distributed and make any necessary adjustments.
Step 5: Check and Adjust as Needed
Once you have attached all the zip ties, take a step back and assess your work. Check that the lights are evenly spaced and adjust the zip ties if needed.
Transforming a Pop-Up into a Cozy Camper
You may want to see also
Using Command hooks
Command hooks are a great, damage-free way to hang lights on your camper awning. They are easy to use and can be removed without causing any damage to your awning. You can install pole lights and solar lights using command hooks.
Step 1: Choose the right type of lights
Before you start, make sure you have the right type of lights for your camper awning. LED pole lights or solar lights are a good option, as they are energy-efficient and long-lasting.
Step 2: Choose a location for the lights
The best spot to hang your lights is usually along the edge of the awning, where they will be out of the way and won't block your view.
Step 3: Attach the command hooks
Attach the command hooks to the awning at evenly spaced intervals. Make sure you use the appropriate size of hooks for the weight of your lights. The hooks should be able to bear the weight of the lights without falling off.
Step 4: Hang the lights
Once the command hooks are in place, you can start hanging your lights. Carefully hang the lights from each hook, making sure they are secure and won't swing around or fall off.
Step 5: Plug in the lights and enjoy
Once all the lights are hung, plug them into a power source and enjoy your beautifully lit camper awning!
Camper Options for a $25,000 Budget: Exploring the Best Buys
You may want to see also
Using clips
Globe Lights:
If you want to hang globe lights on your camper awning, you will need the lights, a ladder, and awning clips. Before you begin, ensure that the area around your camper is clear of debris. Then, follow these steps:
- Using the ladder, reach up and clip the lights onto the awning.
- If your awning has grommets, thread the string of lights through them.
- Begin at the edge of your awning and work your way across, ensuring that the lights are evenly spaced.
- Once you have finished hanging the lights, switch them on and enjoy your beautifully lighted awning.
Solar-powered Awning Lights:
Hanging solar-powered awning lights on your camper awning with clips is a three-step process:
- Clean the awning area where the clips will be placed to ensure proper adhesion.
- Measure the size of the frame and cut the lights to size. Remove the adhesive backing from the lights and install them on the awning, positioning them evenly.
- Use the clips to secure the light strands in place. The solar panel can be clipped to a surface or staked into the ground.
General Tips for Using Clips:
When using clips to hang lights on your camper awning, there are a few things to keep in mind:
- Choose the right type of clips for your awning. Some options include plastic clip-on clothespins, binder clips, or specialised RV awning light clips/hooks.
- Ensure that the clips are attached securely to the awning before hanging the lights.
- If using clothespins or binder clips, point the clipping end upward to prevent the lights from accidentally dropping.
- Consider the weight of the lights when choosing and spacing your clips to ensure they can bear the load.
Building Beds in Campers: A Step-by-Step Guide
You may want to see also
Using clothespins
First, find a spot on your awning where you want to hang the lights. A good starting point is to hang them around the border or along one of the seams of the awning. Once you've decided on the location, use a tape measure to determine the length of the string of lights needed. Cut the lights accordingly.
Next, take your clothespins and attach them to the string of lights at evenly spaced intervals. Make sure to leave enough space between each clothespin to avoid crowding, but also ensure they are close enough to provide adequate support for the lights.
Once all the clothespins are in place, carefully lift the string of lights and clip it onto the side of your awning. Ensure that the string is secure and taut before letting go. Be sure to point the clipping end of the clothespins upward so that they don't accidentally slip and cause the lights to fall.
Finally, plug in the string of lights and enjoy your illuminated camper awning! You can also use battery-powered lights if an outlet is not accessible.
The Prius: Camper-Towing Capacity?
You may want to see also
Using rubber slot fixtures
First, measure the length of the awning and cut the lights to size. After cutting the lights, peel off their adhesive backing and attach them to the awning, ensuring that they are evenly spaced.
Next, use a drill to make holes in the awning at evenly spaced intervals. The size of the hole will depend on the size of the rubber slot fixture.
Thread the string of lights through the holes, and then insert the rubber slot fixtures. Keep them snug so that the lights don't move around.
Finally, connect the lights to an outlet, and you're ready to go!
This method transforms the rollout bars on the RV's awning into instant "track lighting." However, keep in mind that you will need to remove the lights and fixtures when it's time to close the awning.
Transforming Camper Tables: A Cozy Bed Solution
You may want to see also
Frequently asked questions
There are several ways to hang camper awning lights, including zip ties, command hooks, clips, clothespins, rubber slot fixtures, and strip lights.
Camper awning lights brighten up your space and create a special atmosphere, providing additional light and ambiance to your space.
First, choose the perfect spot for your lights, then measure the length of the string of rope lights to determine how many zip ties you'll need. Cut the zip ties to size, leaving about an inch of tail on each. Next, string the lights through the holes in the zip ties, and attach the zip ties to the RV awning by wrapping them around. Finally, adjust the zip ties as needed to ensure the lights are evenly distributed.
First, choose a location for the LED lights, usually along the edge of the awning. Then, attach command hooks to the awning at evenly spaced intervals, ensuring they are the appropriate size for the weight of the lights. Finally, hang the LED lights securely from the command hooks and plug them in.